Tnere’s nothing like a jackleg fence when it comes to stopping cows from accessing that greener grass on the other side. Here in Powell County, Montana, jackleg is also mighty expensive stuff, especially if the property owner opts for treated posts and rails. That wasn’t always true in the past, especially if the rancher or farmer had native materials growing on his land. Forget chemical treatment, slap up raw wood, and about all you had to purchase were the spikes.
Now even the spikes are old school. Construction screws, dude. Hammer? Naw. Battery powered impact driver…as long as you carry enough batteries on your fence-making jaunts.
Growing up on a ranch west of Drummond, Montana–and working on a freeway fence construction crew in my twenties–I never worked with jackleg fencing. On the ranch, it was all barbed wire except for the corrals, which were post-and-rail. The freeway fencing involved both barbed wire and woven wire.
All of it included posts, both T-posts (steel, pounded into the ground) and wooden posts (planted in holes dug with shovel and crowbar).
My first little bit of fencing on the Holy Waters Ranch acreage would also be my first-ever adventure in jackleg fence construction. A mile of it? Um…no. Not hardly, though the ranch does have something like 2 2/3 miles of perimeter fencing and probably 2/3 of that does need attention. Most of that’s also barbed wire. Treated jackleg retail cost for materials could run around $8.00 per foot (give or take, depending on how lucky or skilled you are at sourcing posts and rails, whether you use 5′ or 6′ crossbuck posts, what diameter rails you install, how many per section, whether you build in 12′ or 16′ sections, etc.) $8.00 x 14,000 feet ( 2 2/3 miles, rounded off) = $112,000.
Jackleg fencing in specific situations, however, is the only way to go. Just west of Monture Creek, the land slopes steeply up 100 feet or so, through heavy brush and considerable small timber, crosses a dozen feet of level, clear “walkway”, then slopes up a bit more to a barbed wire fence corner. Away from the steep, out in the open, it’s a bit less than 50 feet. When I first hiked the fence line, an old, rotten jackleg fence section ran from corner to creek.
What was left of it, that is.
Over time, mostly just working a couple of hours every Monday afternoon, I cleared the old, rotten stuff and young, growing juniper trees from that “open” area, piling the discards along the lower, brushy fence remains. Looked to me like all I’d need to fence was…50 feet, according to the tape measure.
Getting started at Holy Waters required some thinking. I did consider barbed wire. After all, it’s what I know. It would be cheaper by far, mostly because only three treated posts would be needed to construct a “brace” section at the downhill end of the gap. The uphill end could be anchored to an existing post. But for this terrain, barbed wire also presented at least one significant problem in that there would always be wire tension providing upward “pull” on the post positioned where the ground levels off. A T-post would be out of the question. Did I want to dig three post holes, each of them preferably three feet deep?
Frankly, no, I did not want to do that. My back had been bothering me for weeks (excuse) and I was lazy (truth). Never mind that chiropractor Mike Welker of Butte got my spine all squared away later; the decision was made.
With jackleg fence, there are no holes to dig. Most importantly, jackleg couldn’t care less if the terrain under it is up, down, or sideways.
In the end, I came up with an ancient, battered, yet totally workable 10′ flatbed trailer. How old is it, you ask? I’m not sure, but one tire’s max pressure listing is 40 psi…and the other is 35 psi. The hitch is sloppy and the securing bolt so rusted in place that it refuses to budge. Wiring the hitch lever in place is the only way to keep it from flying open. The wood bed is in terrible shape. Taillight wiring has long since disintegrated.
You get the picture.
My ranching brother in law donated an entire set of older, 18 volt impact wrenches and batteries. “You might as well have them,” he said. “I don’t do much with 18 volt any more.” I got a deal on the posts and rails. Our local building supply store in Deer Lodge had the necessary construction screws in stock.
For weeks, planning this out, I’d been plagued with step-by-step worries:
- How hard was it going to be for my half ton GMC Sierra pickup truck to tow a load of posts and poles up Helmville Canyon? That sucker is steep, twisty, narrow, and did I mention steep? I mostly worried about the transmission, which has already been rebuilt twice. —————————————————————————————————-
- What if that sloppy hitch came apart? Huh? Huh? ————————————————————-
- How tricky was it going to be, diving off into the barrow pit from Highway 200 west of Ovando, what with all that summer tourist traffic going on up there? ————————————————————————————————-
- On the circuitous uphill route, cross country, to reach the fencing site, how likely was the lowslung hitch to get hung up while crossing the one worst dip in the trail I’d scouted?
In the end, it wasn’t bad at all, demonstrating once again that the things we most often worry about do not always come to pass. The loaded trailer pulled smoothly, nothing but the occasional loose-hitch -clunk!- to give it away. Locking the tranny in second gear did the trick up Helmville Canyon, keeping the revs above 2000 rpm and pulling right along. Traffic proved not to be a problem this day.
Break time: Nearly 2:00 p.m., Trixi’s Antler Café at Ovando, Montana. Chiliburger for breakfast (which I’d skipped) and lunch combined.
Back on the highway, 3 1/2 miles west, dive down off the highway just west of the Monture Creek bridge, and….yay, everything held together. Through the gate, up onto the property, wind around, climb, jam through the low spot. Hitch did plow a shallow trench there for a foot or two, but no big. Up over the final rise, turn around, back carefully down, and it’s time to go to work.
Photos of the fence-making process would have been nice but I didn’t dare. Getting the work done was simply more important. I had to keep my laser-like focus, make the decision to build a four-rail rather than a three-rail fence (knowing I had plenty of rails), lining up each crossbuck post set so the fence remained straight and true (nothing uglier than a wavy fence line constructed by somebody who obviously doesn’t know–or doesn’t care–what he’s doing), etc.
A few of the rails were one step away from being petrified, they were so hard. Leaning on the impact driver for all I was worth, adding a bit of arm squeeze and burning through battery juice like crazy, several of the screws tested things to the limit.
Got it done, finally, at 6:30 p.m. in a light, Oregon style rain. Took a few pictures despite the precipitation, holding one hand over the camera to keep it from getting wet. The fence looked good. I even got cocky and jumped down from the top rail a time or two, slamming my boots on the ground hard enough to remind me that I land harder than I did half a century ago but doing no damage. Hot diggety.
The new jackleg fence section should last for decades. It’s also taller, with more rails per section, than the older, rotten stuff. Even so, that “old stuff” combined with terrain, vegetation, and scrap, provides a decent barrier to bovine grass prospectors. All in all, this portion (down to Monture Creek) should be okay, even if two thirds of it does depend greatly on Mother Nature.
See the seeming “leaning” angle of that old post? That’s a hint. Right past that point, the slope drops down again, abandoning the level “cattle walkway” and plunging toward Monture Creek.
That’s really a downhill drop in the above photo. The picture just didn’t manage to make it obvious.
On the way back down the hill, I did get to see several “wild-flying” birds. Don’t know their species, couldn’t get a picture, but they flapped their wings at incredible speed while mostly hovering in place, sometimes for a minute or more, then darted off and down, disappearing in the grass.
Farther down, one gopher scurried from hole to hole as the truck passed by in granny gear.
Out through the barbed wire gate, close the gate, scramble up on Highway 200, cross the bridge, turn in to the main Holy Waters gate, and…whew. And what a relief it is, a decent shift and no disaster. Now for a place to–there. Drop the trailer, chain and padlock it to a cottonwood tree, just enough to keep honest folks honest. The ranch may not have any trespassers in the near future, who knows? Plus, any self respecting thief would be ashamed to steal that trailer. But come colder weather, I’ll be absent for the many months of winter around here.
For that matter, I’m only there once a week as it is.
Thus ends the first installment of the cowstopper saga, jackleg fence style. It’ll be time next week to take a second look at the stretch of barbed wire fence west of the new jackleg section. If memory serves, there are two places where the wire needs repair, tightening and splicing and maybe replacing a post or two.
In the meantime, let’s close with a photo from last week, a small plant with pink-and-yellow flower petals, the pink ones being heart shaped. No clue what they are, except that they’re pretty cool.
Wait. There’s one more, a bush with red-orange berries. As a kid, we called these “gooseberries” but it’ turns out that’s inaccurate as gooseberry bushes have thorns and these do not. As nearly as I can tell, this is the common bearberry aka Kinnikinnick, Arctostaphylos uva-ursi.